PÜRKAY-BİO 019/01 Polyurethane Self Leveling
Solvent-free, colored, plastic-elastic, self-leveling, two-component polyurethane floor coating material
Characteristics and Properties
PÜRKAY-BIO 019/01 is a self-leveling, solvent-free, two-component, polyurethane-based, plastic-elastic flooring material, produced with sustainable resources. It provides safe use due to its solvent-free nature. Impact and abrasion resistant PÜRKAY 066 PU top coat paint,
where UV resistance is required, PÜRKAY 076 PU top coat paint or new generation water-based PÜRKAY 086 top coat paint should be applied on top.
Also has the following properties:
– impermeability to liquids and resistance to chemicals
– resistance to impact
– crack bridging
– easy cleaning and care (decontamination/ hygiene)
Typical use
Show-rooms, restaurants, offices, shopping areas, production facilities, industrial buildings, warehouses, commercial greenhouses, hospitals. PÜRKAY-BIO 019-01 is part of a polyurethane flooring system, for floor system details please visit our web site www.purkay.com
Substrates
Concrete, stone, brick, rock, metal, wood (mdf, plywood, OSB…) and similar construction materials.
Specifications
| Colour : | Main RAL colours |
| Mixing ratio : | Main Component : Hardener = 4 : 1 (by weight) |
| Pot-Life: | 40 ± 5 minutes |
| Consumption: | A self leveling coating with a thickness of 1 mm can be achieved by use of 1.38 kg/m² of PÜRKAY-BIO 019/01 Recommended thickness is 2 mm |
| Curing time: | Depending on relative humidity and temperature, 12 hours |
| Density (25°C): | Main component : 1.47 ± 0.05 gr/cm³ Mixture: 1.38 ± 0.05 gr/cm3 |
| Viscosity (25º C): | Main component : 3.300 ± 500 mPas (rotor 2, V:6) Hardener: 210 ±30 mPas (rotor 2, V:30) Mixture : 1.500 ± 300 mPas (rotor 2, V:12) |
| VOC: | 0 |
| EURegulation2004/42: | According to the EU-Directive 2004/42 the maximum allowed content of VOC is 550/500 g/L (Limits 2007/2010) fort the ready to use product. |
| TOC: | Mixture: 41-49% |
| Chemical Resistance : | Resistant to diluted acid, water, fuel and mineral oils. |
| Service Temperature: | Approximately 100ºC |
| Fire Resistance: | Report No: AB-0001-T 80802 Test was made according to Turkish Standart TS EN ISO 11925-2 with a positive result. Tested products correspond with the 2. EFL class of Chart TS EN 13501. |
| Hardness: | Shore D: 35 ± 5 (D2240-05) |
| Compressive Strengt: | 30 N/mm 2 (DIN 53 454) |
| Tear Resistance: | 9.82 N (D 624-00) |
| Tensile Strength: | 5.8 N/mm 2 (D 412-060) |
| Elongation: | 160% (D 412-060) EU |
| Contents: | The Hardener consists of polymeric MDI, which has Low vapor pressure enabling safe use of the product. The Resin consists of mixtures of polyether and polyester resin as well as pigments and fillers |
| Storage: | Can be stored in original container, for 1 year under 35°C and protected from freezing |
| Packaging: | Main component : 16 kg can – Hardener : 4 kg can |
| Cleaning: | Cleaner 314 |
Technical hints
The mixed material must be used within the pot-life, otherwise irreversible gelation of the product occurs. All equipment must be cleaned immediately after use. Use of protective rubber gloves is recommended.
Pretreatment
The substrates to be applied must be free of loose particles, oil, grease and other impurities. Special attention should be paid to the moisture content of the substrate to ensure that there are no other adhesion problems or undesirable side-reactions. For successful results, concrete substrates should have a moisture content of <5% and application should be carried out at a substrate temperature equivalent to the prevailing dew point plus 3°C. The substrate must be primed with PÜRKAY Epoxy Concrete Primer. Defects must be repaired with PÜRKAY 022/A filler. In case of negative water pressure or moisture content higher than 5% or newly applied concrete, special primer PÜRKAY Epoxy Moisture Barrier should be used. In case PÜRKAY-BIO 019-01 is going to be applied in several layers, the re-coating window between layers should be within 6-24 hours. In places where the 24 hour period is exceeded, the surface should be roughened by sanding (sanding paper or scotch brite).
Application
PÜRKAY-BIO 019-01 comes in two separate cans. The whole content of the smaller can, the ”Hardener” should be mixed well with the content of the larger can, with the ”Main Component”. The mixing of the two components can be done with the help of an electrical mixer, such as a stirrer attached to a power drill. Application of the material can be achieved by help of trowel. The applied surface must be protected from water for at least 8-10 hours.
Note:
Avoid skin contact with Hardener, all soiled equipment and such should be cleaned immediately. Do not induce vomiting, seek for medical advice. Use protective goggles and gloves.